Luxor ZD/ZDC

Welcome to the Luxor Support Section. Here you will find instructions to install and program your landscape lighting controller. Proper installation and setup will allow you to take full advantage of all the features the Luxor has to offer.

Support Topics
  • Firmware Update
    To update the Firmware on the Luxor Power Controller, you'll need an SD card to transfer the data from a computer to the facepack.   The SD card must be a regular SD or SD-HC. 
  • Locating the Transformer
    Locate transformer(s) in a well-ventilated area away from direct irrigation spray and central to where the majority of the lighting fixtures will be installed. The goal is to
  • Mounting Transformers
  • Remotely Locating the Facepack
    The facepack mount is used to mount the facepack in a remote indoor location to provide easier access to the Luxor. When installing the Luxor FP Mount with WIFI module, the antenna
  • Running Cables to Fixtures
    Once the transformer has been installed and all fixture locations determined, the next step is to run the correct size cable from the transformer to the fixtures. LED fixtures
  • Surge Module
    The SURGE MOD is designed to provide two additional layers of surge protection to any low-voltage LED fixture. The module should be used in areas prone to frequent surge events (e
  • Operating the Luxor
  • Setting up Programs
    The PROGRAM Screen is where all daily running Programs designated by a letter are setup.  Programs are set by calling up fixtures that have been assigned to Groups or Themes. For
  • Manual Mode
  • Themes
  • Grouping Light Fixtures
    The lighting assignment screen is an automatically displayed screen when an FX ZD fixture or board is connected into the Programming Ports of the facepack. This mode can also be
  • Setup
    SETUP is the user management area of the Time, Date, and Time Zone settings.  SETUP is also where the Location and Assignment functions are also accessed.
  • Location
    The LOCATION menu is designed to graphically represent a Luxor’s location on a map for correct Sunrise and Sunset times based on the current date.
  • Shutdown
    The SHUTDOWN menu option is a way to completely shut down all lighting events in the MANUAL and PROGRAM modes regardless of time or status, indefinitely. This mode does not turn
  • Contact Card
    Every Luxor ships with the FX Technical Support contact information as the default image. The image is changed by following the steps below: Save desired image on an SD card.
  • Installing the LAM
    The LAM plugs into the headphone jack of a smartphone or tablet. Plug the LAM into the smart device, open FX Wi-Fi App and enter the Assignment Mode, choose the new fixture group,
  • Wi-Fi Module & Antenna
    There are two main components of hardware that must be installed: the module and the antenna. Before beginning the installation of the hardware and module, click here to download
  • Installing the LAN
    A direct connection between the controller and the network equipment can provide a more reliable connection. When planning for a CAT 5, 5e, or 6 connection between the router and a
  • Setting up a Wi-Fi Network
    There are two ways to associate a Luxor Controller with a Wi-Fi network: through a networked Wi-Fi router, or directly to a wireless iOS or Android device.  A strong WIFI signal
  • Checking Signal Strength
    Signal Strength is consistent where the facepack and Wi-Fi Module are located. We recommend a 70 RSSI level or greater for consistent WIFI signal.  If the signal is low or
  • LAN Module Network Connection
    Installing a LAN module for a direct connection between the Luxor and the network equipment can provide a more reliable connection. Before beginning the steps below, please ensure
  • Direct Connect
    The Luxor can be placed in Direct Mode which allows an iOS or Android device to connect directly over Wi-Fi to a single controller. This removes the need to go through the Wi-Fi
  • iOS and Android Control
    There are two ways to associate a Luxor Controller with a Wi-Fi network. Through a Networked Wi-Fi Router, or directly to a wireless iOS or Android device. A Luxor system with a
  • Manually Configuring a Controller
       
  • Connect Wi-Fi Router
    There are two ways to associate a Luxor Power Controller with a Wi-Fi network, through a Networked Wi-Fi Router, or directly to a wireless iOS or Android device. For instructions
  • System Requirements
    Luxor Linking allows for a single point of control on sites requiring multiple Luxor ZD or Luxor ZDC controllers. Linking sites consists of a primary and one or more satellite
  • Firmware Update Procedure
    Step 1: Download the latest Facepack and Chassis Luxor Linking firmware onto an SD Card.   Step 2: Update
  • Connecting Satellite Controllers
    .step-container { margin: 0 auto; height: auto; max-width: 700px; width: 100%; } .step-linking { display: inline-block; float: left;
  • Chassis Communication and Assignment
    Step 1: Apply power to Primary controller.   Step 2: From the HOME screen, push both the HOME and the HELP
  • System Example
    Luxor Linking allows users to hardwire up to nine Luxor Satellite controllers, while maintaining a single point of control. The addition of Luxor Satellite controllers reduces

ZDC - Color

  • Mixing/Grouping FX LED ZD and ZDC
  • iOS and Android Control Color
    The Luxor ZDC system adds color to existing zoning and dimming options. A color system requires that a ZDC LED board is installed into each desired FX LED fixture. It also requires
  • Converting to Color
    Luxor offers both zoning and dimming capabilities that provide virtually limitless design possibilities.  The new Luxor ZDC has all the features of the Luxor ZD + Color. ZDC offers
  • Color Wheel
    The color wheel feature scans through all 300 hues constantly at intervals determined by the user. The scan is applied at the group level, allowing various groups to cycle at
  • Quick Start Color Guide
    The ZDC Color boards are available in three options, ZDCKITL, ZDCKITM, and ZDCKITR. Below you will find quick specifications needed when sizing the transformer using color LED
  • Checking Voltage Overview
    Using a digital voltmeter allows you to take important voltage readings at the transformer, at each fixture and at the receptacle the transformer will be plugged into. Dial the
  • Resetting Controller
    Resetting the Luxor power controller will erase the current program data and restart the controller.
  • Determining Shorts and Overload Conditions
    The Luxor transformer showing Error Overloaded can indicate 2 possible problems.  1. If the overload message has a lower case “o”, this indicates a current in excess of the
  • Fuse Replacement
    If the unit is powering on but the fixtures attached are not receiving power, the fuse may need to be replaced. To replace, follow the directions below: Unplug the Luxor ZD
  • Not Showing Map
    The Location menu is designed to graphically represent a Luxor's location on a map for correct Sunrise and Sunset times based on the current date.   
  • LED Board Flashing
    The most common reason for an LED board inside a fixture to flash would be a drop in voltage.  A voltage drop in an electrical circuit normally occurs when current is passed
  • Upgrading ZD/ZDC
    When upgrading a Luxor ZD or ZDC unit to a LUX150/300, the front panel must be replaced. Additionally, if your system includes a Wi-Fi module, it will need to be upgraded to match
  • Cables
  • Suggested Maintenance
    Periodic system maintenance is required to keep your FX lighting system operating at peak performance. Practicing these maintenance suggestions will lengthen the life and enjoyment
  • Backing Up Programs
    The programming in the Luxor Controller can be backed up using an SD card. IMPORTANT: The SD card must be a SD or SD-HC. SD-XC should NOT be used. SD-XC cards do not work
  • Recommended splicing options
    DBRY-6 Direct Bury Splice Kit With any low voltage lighting system, waterproof connections are crucial to maximizing the life of the system. 3M's DBRY-6 shown here are the
  • Themes and Groups
    With theming technology, different parts of your landscape can now offer completely different environments, automatically. The image below should help explain the simplicity to
  • Only two terminals?
    The Luxor transformer requires fewer wire runs to communicate with fixtures, therefore multiple fixture groups can share the same wire run. It's because of this
  • Warranty
    The Luxor Transformer is warranted from manufacturer's defects for a period of ten years from the date of installation.

Get FX Luminaire